Phison MPtool is a factory-grade tool. If you select "Pre-format" or "Full Capacity" with incorrect settings, you will permanently convert your USB drive into a 0MB brick that no tool can detect. Always verify your controller ID before proceeding.
Backup your data. There is no undo.
To repair or reflash a flash drive with the Phison PS2251-07 (PS2307) controller, you generally need the Phison MPALL (Mass Production Tool) or UPTool utilities. 🛠️ Required Tools
Utility: Phison MPALL (standard) or UPTool (for low-quality flash or deep errors). Firmware Files: You need two specific .BIN files: Burner (BN): e.g., BN07V106M.BIN. Firmware (FW): e.g., FW07FF01V10210M.BIN.
Identification: Use ChipGenius to confirm your controller is exactly PS2251-07 and to find your Flash ID (FID). ⚡ Installation & Setup Steps Phison MPALL v5.13.0C - USBDev.ru
To install and use the Phison Mass Production Tool (MPTool/MPALL) for controllers like the PS2251-07 (PS2307) , follow these steps to reflash or repair your USB drive. 1. Preparation & Identification
Before starting, ensure you have identified the exact hardware specifications of your drive. Verify Controller : Use a tool like ChipGenius Flash Drive Information Extractor to confirm your controller is specifically (also labeled as Check Mode
: If your drive is not recognized, it might be in "2307 PRAM" or "panic" mode. This typically happens if the firmware is corrupted. : Flashing will erase all data on the NAND chip. 2. Download Required Files
You need three main components, often found on archival sites like Phison MPALL (v5.13.0C or similar) : The main production utility. Burner File (BN07
*: These are the "burners" used to prepare the controller for the firmware. Firmware File (FW07
*: The specific firmware image for the PS2251-07/PS2307 controller. 3. Installation & Setup Extract the MPALL distribution : Unzip the tool to a local folder on your PC. Run the Utility MPALL_F1_9000_vxxx.exe as an Administrator. Configure the Tool and select Basic Adjustment New Setting Controller Flash Setting , point the "Burner File" and "Firmware File" paths to the files you downloaded.
(Optional) Customize the Manufacturer Name or Product ID (PID) if desired. Save Configuration to return to the main window. 4. Flashing Process Connect the Drive : Plug your USB drive into a USB 2.0 port
if possible, as these tools often struggle with USB 3.0/3.1 ports during the flashing process. Update View : Press the
button in the MPALL window; your drive should appear in one of the slots. to begin the process.
: Do not disconnect the drive or turn off your computer during this stage, as it can permanently brick the device. Completion
: Once the bar turns green (PASS), disconnect and reconnect the drive. The computer should now recognize it as a fresh, working device. Troubleshooting Device not found
: If the tool doesn't see the drive, you may need to manually enter "Test Mode" by carefully shorting the pins on the NAND chip, though this is only for advanced users. Slow performance
: If the drive is slow after flashing, you may have used an incompatible firmware version or need to perform a "Low Level Format" within the tool. HDD GURU FORUMS for your particular NAND type?
To install and use the Phison MPTool (MPALL) for controllers PS2251-07 (PS2307), you should use the Phison MPALL production software. This tool is primarily used for deep repair of corrupted flash drives or updating firmware. 1. Preparation and Tool Selection
Before starting, identify your flash drive's controller and memory chip details using a tool like ChipGenius to ensure compatibility. phison ps225107ps2307 mptool install
Compatible Tool Versions: For the PS2251-07 controller, recommended versions include Phison MPALL v3.70.0E, v3.72.0B, or specialized versions like MPALL_F1_7F00_DL07_v503_0A specifically for eD3 memory.
Where to download: You can find these utilities and their corresponding binaries in the Phison Electronics section of USBDev.ru. 2. Configuration Steps
The "installation" is typically a portable execution followed by a specific setup:
Unpack the Utility: Extract the MPALL distribution to a folder on your local drive.
Launch MPParamEdit: Run MPParamEdit_F1.exe from the folder to create a configuration file. Basic Settings: Select "New Setting" and click OK. In the Controller dropdown, select PS2251-07. Set Host Port to match your USB port type (2.0 or 3.0).
Firmware Selection (Optional): If the drive is severely corrupted, you may need to add "Burner" and "Firmware" files (e.g., BN07*.bin and FW07*.bin). Consult the MPALL Repair Guide on USBDev.ru for help selecting the correct binary versions based on your memory type.
Save Config: Click "Save" to generate the MP.ini file and close the editor. 3. Execution
Run MPALL: Open the main executable (e.g., MPALL_F1_9000_v372_0B.exe).
Detect Drive: Insert your flash drive and click "Update". The device should appear in one of the slots.
Start Repair: Click "Start". Do not disconnect the drive until the process finishes and the slot turns green. Alternative: Phison ST-Tool
If MPALL does not recognize your device, you might try Phison ST-Tool (versions 3.67, 3.70, or 3.71), which is another production flasher designed for the PS2251-07 chip.
Important: These tools perform low-level operations that will erase all data on the drive. If the tool hangs between attempts, check your Task Manager and kill any lingering MPALL processes before trying again. Phison MPALL v5.13.0C - USBDev.ru
Phison PS2251-07 (also known as PS2307) is a popular USB 3.0 controller found in many flash drives, including brands like Kingston and Toshiba. When these drives become "write-protected" or "unrecognized," specialized Mass Production (MP) tools are required to reflash the firmware and restore functionality. Essential Tools for PS2251-07/PS2307
To repair this specific controller, you will typically need one of the following from specialized repositories like Phison MPALL (v5.03.0A or newer): The professional-grade mass production tool. Version
is specifically recommended for PS2251-07 controllers using eD3 flash memory. Phison UPTool:
A simpler alternative used when MPALL fails to recognize the drive. Phison Format & Restore Tool:
A "one-click" end-user utility that can sometimes fix minor firmware glitches without complex manual configuration. Installation & Flashing Procedure This process is high-risk and will erase all data
on the drive. It may also permanently brick the device if incorrect firmware is used. Identify Your Hardware: Use a tool like ChipGenius to confirm your controller is indeed a PS2251-07 (PS2307) and note the (e.g., Toshiba or Hynix memory). Download MPALL:
Extract the MPALL distribution (e.g., v5.13.0C or v5.03.0A) to a local folder. Configure the Tool: MPParamEdit_F1.exe to create a configuration file ( Controller dropdown, select Select "Basic Adjustment" and "New Configuration". Input the correct VID and PID (commonly for Kingston). Connect the Drive: Plug your USB drive into a USB 2.0 port Phison MPtool is a factory-grade tool
if possible, as some MP tools struggle with USB 3.0 drivers during the flashing process. Start Flashing: MPALL_F1_...exe to see your drive in the list. to begin the low-level format and firmware burn. HDD GURU FORUMS Troubleshooting Common Errors No Drive Found: Try running the tool on Windows XP or Windows 7 (x86)
, as modern Windows 10/11 security often blocks the low-level drivers needed by MPALL. Check Sum Error:
In newer DL20 versions of MPALL, you may need to manually bypass checksum verification in the 2307 PRAM / Panic Mode:
If the drive identifies as "2307 PRAM," it has entered a manufacturing mode. You may need to "short" the NAND pins to force the controller into a state where it can accept new firmware. HDD GURU FORUMS for a specific tool like Phison MPALL HDD GURU FORUMS • View topic - Phison PS225107 USB Drive.
Phison PS2251-07 (also known as PS2307) is a popular controller found in many USB 3.0 flash drives. When these drives become "Write Protected," "No Media," or fail to format, the Phison MPTool (Mass Production Tool) is the primary utility used to reflash the firmware and restore the device to factory settings.
This guide covers the safe installation and usage of the Phison PS2251-07 MPTool. 🛠️ Prerequisites Before Installation
Reflashing a controller is a high-risk procedure. Ensure you have the following ready:
ChipGenius or Flash Drive Information Extractor: Use these tools to confirm your controller is exactly PS2251-07 or PS2307.
Correct Firmware Files: MPTool requires .bin files (Burner and Firmware) specific to your NAND flash type (e.g., Toshiba, SanDisk, Hynix).
Windows Environment: These tools are designed for Windows (preferably Windows 7 or 10). Run them in Administrator Mode.
Backup: Flashing will securely erase all data on the USB drive. 📥 How to Install and Set Up Phison MPTool
The "installation" of Phison MPTool is usually a portable extraction process. Follow these steps to get started: 1. Extract the Software
Download the version of MPTool compatible with PS2251-07 (often found in packages labeled MPALL_F1_9000 or similar). Extract the ZIP folder to your desktop. Avoid running it directly from the ZIP. 2. Configure the MP.ini File
Before opening the application, you must configure the settings: Locate the file named MP.ini or Settins.ini in the folder. Open it with Notepad.
Under the [PenDriveID] section, ensure the VID and PID match your device (common Phison defaults are 0000 and 0000 or 13FE and 5200). 3. Run as Administrator
Right-click MPALL_F1_xxxx.exe and select Run as Administrator. If the program doesn't see your drive, try a USB 2.0 port, as USB 3.0 ports can sometimes cause detection issues during flashing. 🔄 Using MPTool to Flash PS2251-07 Once the tool is open, follow this workflow:
Update/Refresh: Click the "Update" button to let the tool scan your USB ports. Your drive should appear in one of the white boxes.
Setting: Click the "Setting" button. Select "New Setting" and click OK.
Controller Selection: In the configuration window, select PS2251-07 from the Controller dropdown. Firmware Loading: Burner: Select the .bin file starting with BN07. Firmware: Select the .bin file starting with FW07. Where to find it:
Save and Start: Save the settings to return to the main screen. Click Start.
Warning: Do not unplug the drive while the progress bar is moving. A "Green" box indicates success; a "Red" box indicates a firmware mismatch or hardware failure. ❓ Troubleshooting Common Errors
CT - 0x1042: This usually means the firmware file is incorrect for your specific NAND flash. Double-check your flash type in ChipGenius.
Drive Not Found: Try a different USB port or use a "Test Mode" (shorting pins on the controller), though this is only recommended for advanced users if the drive is totally bricked.
Read Only Error: Ensure you have toggled the "Low Level Format" option within the MPTool settings.
If you'd like to troubleshoot a specific error code or find the exact firmware version for your flash memory: Tell me the Flash ID from ChipGenius (e.g., AD3A14AB). Share the specific error code you're seeing in MPTool. Confirm your NAND type (TLC, MLC, or SLC).
To install and use the Phison MPALL (Mass Production Tool) for the PS2251-07 (PS2307)
controller, follow these steps. This utility is typically used to repair "Write Protected" errors, restore "unrecognized" drives, or reflash firmware. cdn.prod.website-files.com Prerequisites Identify Your Device : Use a tool like ChipGenius Flash Drive Information Extractor to confirm you have the Phison PS2251-07 (PS2307) controller and to note your NAND Flash-ID Download Software : Obtain the
distribution (e.g., v3.72, v5.03, or newer) from reputable repositories like FlashBoot.ru Obtain Firmware Files : You will need a Burner File (starting with Firmware File (starting with ) that match your NAND type. cdn.prod.website-files.com Installation & Configuration Steps Extract Files : Unzip the MPALL distribution to a folder on your PC. Open Configuration Utility MPParamEdit_F1.exe (or a similar from the folder). Basic Setup "Advance Setting" "New Setting" Controller Enter your device's (found earlier via ChipGenius). Assign Firmware "Burner File" field, select your "Firmware File" field, select your : You can often check "Auto ISP" to let the program attempt to select these automatically. Save Config : Save the settings as or similar in the same directory. Flashing the Drive : Launch the main executable (e.g., MPALL_F1_7F00_DL07_v503_0A.exe Connect Drive
: Plug in your USB drive. If it is "dead," you may need to put it into
(shorting specific pins on the chip) for it to be recognized.
to detect your drive. It should appear in one of the numbered boxes. to begin the mass production process. : This process will permanently erase all data on the drive. : Wait for the box to turn
(Success). If it turns red, an error code will be displayed for troubleshooting. If you need help finding the exact firmware file for your specific memory chip, let me know the AD DE 14 A7 42 4A ) found by ChipGenius. Phison MPALL Flash Drive Repair Guide | PDF - Scribd
For the PS2251-07/PS2307, the following versions are widely confirmed to work:
Where to find it:
Avoid executable downloaders from popup-heavy sites. Look for a clean .zip or .7z archive.
The interface looks like a relic from the Windows 98 era. It is cluttered, technical, and unintuitive.
After success:
| Error Code | Meaning | Solution | | :--- | :--- | :--- | | 0x1042 | Firmware mismatch | You loaded the wrong .bin file. Find the correct FW for PS2251-07. | | 0x1106 | Bad driver | Reinstall Phison driver using DriverInstall.exe. | | 0x1112 | Low-level format required | Check "Erase All" in settings before starting. | | 0x3012 | Timeout / Bad block count | The drive has too many physical errors. Replace it. |
MPTool does not require traditional installation.
Always run antivirus on downloaded tools – some are flagged due to low-level disk access (false positive common).