Routers, switches, and fiber-optic transceivers in remote cabinets or cellular base stations often operate from 48V or 24V. The wide input range of the HYS3C210-CS allows it to handle unstable grid conditions.
1. High-Efficiency Power Delivery
2. Advanced Protection Circuitry
3. "CS" Series Enhancements
4. Thermal Management & Reliability
5. User Interface & Monitoring
It is important to note that the HYS3C210-CS is technically a monitoring device (Load), not a power supply (Source).
Recommended for:
Not recommended for:
| Parameter | Value | |--------------------------|-----------------------------| | Input Voltage | 100–240V AC (50/60Hz) | | Output Voltage | 12V DC (or 24V, check variant) | | Output Current | 17.5A (for 12V; 8.75A for 24V) | | Power Rating | 210W | | Efficiency | ≥86% (typical load) | | Ripple & Noise | ≤120mV p-p | | Cooling | Forced air (built-in fan) | | Protections | Short circuit, overcurrent, overvoltage, overtemperature | | Operating Temp. | -20°C to +60°C (derating above 40°C) | | Dimensions (L×W×H) | Approx. 198×98×42 mm |
| Symptom | Likely Cause | Solution | |---------|--------------|----------| | No output, no LED | No AC input / blown fuse | Check mains, replace internal fuse (slow-blow, same rating) | | Output drops under load | Overload / poor wiring | Reduce load, check wire gauge | | Output cycling on/off | Short circuit / OLP triggered | Disconnect load, test separately | | Unit very hot | Poor ventilation / overload | Improve cooling, derate load | | LED flashing | Over-voltage or over-temp | Let cool, reduce input voltage range |
Fuse replacement: Usually 5x20mm 5A/250V slow-blow (for 230VAC). Confirm before replacing.
Routers, switches, and fiber-optic transceivers in remote cabinets or cellular base stations often operate from 48V or 24V. The wide input range of the HYS3C210-CS allows it to handle unstable grid conditions.
1. High-Efficiency Power Delivery
2. Advanced Protection Circuitry
3. "CS" Series Enhancements
4. Thermal Management & Reliability
5. User Interface & Monitoring
It is important to note that the HYS3C210-CS is technically a monitoring device (Load), not a power supply (Source). hys3c210-cs power supply
Recommended for:
Not recommended for:
| Parameter | Value | |--------------------------|-----------------------------| | Input Voltage | 100–240V AC (50/60Hz) | | Output Voltage | 12V DC (or 24V, check variant) | | Output Current | 17.5A (for 12V; 8.75A for 24V) | | Power Rating | 210W | | Efficiency | ≥86% (typical load) | | Ripple & Noise | ≤120mV p-p | | Cooling | Forced air (built-in fan) | | Protections | Short circuit, overcurrent, overvoltage, overtemperature | | Operating Temp. | -20°C to +60°C (derating above 40°C) | | Dimensions (L×W×H) | Approx. 198×98×42 mm | replace internal fuse (slow-blow
| Symptom | Likely Cause | Solution | |---------|--------------|----------| | No output, no LED | No AC input / blown fuse | Check mains, replace internal fuse (slow-blow, same rating) | | Output drops under load | Overload / poor wiring | Reduce load, check wire gauge | | Output cycling on/off | Short circuit / OLP triggered | Disconnect load, test separately | | Unit very hot | Poor ventilation / overload | Improve cooling, derate load | | LED flashing | Over-voltage or over-temp | Let cool, reduce input voltage range |
Fuse replacement: Usually 5x20mm 5A/250V slow-blow (for 230VAC). Confirm before replacing.