| Aspect | Experience | |--------|-------------| | Frequency | Occurs 1–2 times per year, or after any antenna/signal change | | Ease of fix | Moderate – requires knowing your broadcast type | | Official support | Poor – Samsung forums have many unresolved threads | | Fix permanence | Usually permanent unless signal changes again |
DVB (Digital Video Broadcasting) is the standard used for digital television signals. Samsung TVs utilize a DVB-T2/C/S2 tuner system.
The "Select Type Error" occurs when the TV's software attempts to process a signal stream that does not match the configured input mode. For example, if the TV is internally set to expect a "Cable" (DVB-C) signal stream but is receiving a "Terrestrial" (DVB-T/Antenna) frequency packet, the tuner cannot decode the service information (SI) tables, resulting in this specific error prompt.
The "DVB Select Type Error" is rarely a hardware failure. It is almost exclusively a software configuration issue where the TV expects a specific digital signal format (DVB-T vs DVB-C) that conflicts with the actual input. Performing a Factory Reset followed by a careful Auto Tune with the correct "Air/Cable" selection typically resolves the issue immediately.
The "DVB Select Type Error" on Samsung TVs typically occurs when the television's internal tuner fails to correctly identify or switch between digital broadcast standards (DVB-T, DVB-C, or DVB-S). This hardware-software mismatch often results in a "No Signal" message or a frozen setup screen. Core Causes of the Error
Regional Mismatch: Attempting to use a TV manufactured for a different market (e.g., an EU model in the Middle East) where the DVB protocol version differs.
Corrupted Service Data: Outdated or corrupted channel lists stored in the TV’s volatile memory.
Incompatible Antenna/Cable Feed: The signal being fed into the TV does not match the DVB type selected in the settings. Step-by-Step Troubleshooting Manual Tuning & Signal Reset: Navigate to Settings > All Settings > Broadcasting. Select Expert Settings > Manual Scan.
Manually select the specific Digital Channel Tuning frequency for your region to force the TV to lock onto a known valid signal. Clear Device Cache:
Technical glitches can sometimes be resolved by clearing the system's "Device Care" cache. Go to Settings > Support > Device Care and select Manage Storage to clear cache for broadcast-related apps. Network and Region Refresh:
A network error can sometimes trigger tuner-related faults. If the TV is also failing to connect, perform a Network Reset via Settings > General > Network > Reset Network. Factory Reset via Service Menu:
If standard settings are locked, technicians often use the "Service Menu" (accessed by pressing Info + Menu + Mute + Power while the TV is off) to reset the Region or Local Set parameters. Caution: Changing settings here can permanently disable the TV.
For persistent hardware-level failures, such as a blinking red light indicating a mainboard fault, you may need to Request Service directly from Samsung. How to set up channels on Samsung TV? dvb select type error samsung tv
The "DVB Select Type" error on a Samsung TV typically occurs when the television's internal software gets stuck during a channel scan or fails to recognize the digital broadcasting signal (DVB stands for Digital Video Broadcasting). This message often appears as a persistent overlay that prevents you from accessing other menus or watching TV. Immediate Fixes to Remove the Error
If the "DVB Select Type" notice is stuck on your screen, try these steps in order:
Perform a Soft Reset: While the TV is on, press and hold the Power button on your remote control until the TV turns off and the Samsung logo reappears on the screen.
Power Cycle the TV: Unplug the TV from the wall outlet for at least 30 to 60 seconds. This resets the internal circuitry and can clear minor glitches causing the DVB prompt.
Switch to the Correct Source: The DVB error often pops up when the TV is set to an incorrect input. Ensure your source is set to "TV" or "Live TV" rather than an unused HDMI port. Troubleshooting the Digital Broadcasting Setup
If the error appears while you are trying to set up channels, the issue may be related to your signal or regional settings. How to get the DVB notice off the tv screen.
Errors related to DVB (Digital Video Broadcasting) on Samsung TVs, such as "DVB Select Type" or "New DVB Service Found,"
typically occur when the TV's internal tuner detects changes in the digital signal or when the broadcast settings do not match the input source JustAnswer Common Fixes for DVB Errors
If you are encountering errors or persistent "New DVB Service" messages, try the following: DVB TV Problems - JustAnswer
Troubleshooting the "DVB Select Type" Error on Samsung TVs Seeing a "DVB select type" error or prompt on your Samsung TV can be frustrating, especially when it prevents you from accessing your favorite digital channels. This issue typically occurs during initial setup, after a software update, or when the TV's internal tuner loses its configuration.
DVB (Digital Video Broadcasting) is the international standard for digital television. When your TV asks you to "select type," it is essentially asking which digital signal standard it should use to scan for channels: DVB-T (Terrestrial/Antenna), DVB-C (Cable), or DVB-S (Satellite).
Here is a comprehensive guide to understanding and fixing this error. 1. Understanding the DVB Options | Aspect | Experience | |--------|-------------| | Frequency
Before troubleshooting, identify which signal source you are actually using. Selecting the wrong type is the most common cause of "no channels found" or persistent error messages.
DVB-T / DVB-T2 (Air/Antenna): Use this if you have a physical aerial or "bunny ears" antenna connected to the coaxial port.
DVB-C (Cable): Use this if you have a cable wire coming directly from your wall (without a separate set-top box).
DVB-S / DVB-S2 (Satellite): Use this if you have a satellite dish connected directly to the "Satellite" input on the back of the TV. Samsung re-tune your TV - video 1
It sounds like you're encountering a "DVB Select Type Error" on your Samsung TV. This typically happens when the TV's tuner is set to the wrong DVB standard for your region or when scanning for channels.
Here's how to fix it:
A "DVB select type error" reflects a mismatch between received DVB signaling and the TV's expectations—caused by configuration, firmware limitations, malformed broadcast metadata, hardware faults, or signal problems. Systematic diagnosis (settings, firmware, signal measurement, SI capture) typically isolates the cause; fixes range from simple rescans to firmware updates or broadcaster corrections.
If you want, I can:
Incorrect Input Selection: The TV is set to scan for "Cable" (DVB-C) when you are using an "Air" (DVB-T/T2) antenna, or vice versa.
Outdated Hardware: Older Samsung models may lack the necessary codecs (like HEVC) to process updated digital transmission systems.
Signal Interruptions: Loose coaxial cables or a faulty digital antenna can trigger persistent DVB notices or "No Signal" errors. How to Fix the DVB Error
To resolve the error and clear the notification from your screen, follow these troubleshooting steps: DVB TV Problems - JustAnswer Incorrect Input Selection : The TV is set
The "DVB Select Type" error on Samsung TVs typically occurs when the television's internal digital tuner encounters a mismatch between the broadcast signal type (e.g., DVB-T, DVB-C, or DVB-S) and the user's selected input or hardware configuration
. This often manifests as an inability to find channels or a persistent "New DVB Service Located" notification. JustAnswer Common Causes Outdated Hardware
: Older Samsung DVB tuners may struggle with modern signal compression ratios or changes in digital transmission systems. Incorrect Source Selection
: If the TV is set to an external source (like HDMI or an app) while trying to access broadcast menus, those options may be grayed out or unavailable. Signal Changes
: Recent changes in your region's digital broadcast signal can trigger the "New DVB Service Located" message, as the TV detects new channel types it cannot automatically reconcile. JustAnswer Step-by-Step Troubleshooting 1. Verify the Input Source
The "Broadcasting" and "Auto Tuning" menus are often only accessible when the TV is set to the correct source. button on your remote. Navigate to Connected Devices JustAnswer 2. Perform a Full Auto-Tune
If the tuner has become "confused" by local signal changes, a fresh scan can often clear the DVB type error. Navigate to Broadcasting Auto Tuning Settings Auto Tuning
When prompted for the channel type, ensure you select the one corresponding to your connection: (for an antenna), JustAnswer 3. Power Cycle and Reset
Temporary glitches in the DVB service handler can be resolved with a "soft reset." Soft Reset : While the TV is on, press and hold the
button on the remote until the TV turns off and the Samsung logo reappears. Power Cycle : Unplug the TV from the wall outlet for at least 30 seconds
(or up to 5 minutes) to drain residual energy before plugging it back in. How to get the DVB notice off the tv screen. - JustAnswer
It sounds like you're encountering a "DVB Select Type Error" on your Samsung TV. This typically happens during or after a channel scan (especially if you moved, changed antennas, or reset the TV).
Since you asked to "provide a feature" — I’ll assume you mean provide a fix / solution feature for this error. Below is a step-by-step troubleshooting guide.