Digi Edgeport 1 Driver Windows 10 64 Bit

Although the Edgeport 1 is a legacy device, Digi International maintains a unified driver package that supports it.

Using Digi’s RealPort or PortVision DX tool (downloadable from Digi's website), you can:

Digi International has not officially discontinued the Edgeport 1, but support for Windows 10 64-bit is now in "legacy maintenance" mode.

Even with the correct driver, issues arise. Here is the most frequent error log.

When you plug a Digi Edgeport 1 into a Windows 10 64-bit PC for the first time, you might experience one of three scenarios:

The root cause? Starting with Windows 10 version 1607 (Anniversary Update), Microsoft requires all kernel-mode drivers to be digitally signed by Microsoft’s Hardware Dev Center. Older Edgeport drivers from 2012 or earlier do not have this signature.

A: This occurs if you try to run a pre-Windows 8 driver. Ensure you are using the v7.0.0.2 installer. If still problematic, right-click Setup.exe > Properties > Compatibility > Run this program in compatibility mode for Windows 8 or Windows 7.

A: Yes. Digi continues to provide signed 64-bit drivers for all Edgeport devices, including the Edgeport/1, as part of their legacy product support. The latest driver (v7.0.0.2) is fully compatible with Windows 10 21H2 and Windows 11.

1. "The driver is not signed" / Digital Signature Error If Windows 10 blocks the driver because it lacks a digital signature (common with very old legacy drivers): digi edgeport 1 driver windows 10 64 bit

2. Device Not Detected

3. COM Port Number too High Some legacy software cannot access COM ports numbered higher than 8 or 9.

The latest official driver for the Digi Edgeport/1 on Windows 10 (64-bit) is version 6.05. While the Edgeport line is officially designated as "end of life" by Digi International, this driver package remains compatible with modern 64-bit Windows environments. Download and Installation Steps

Follow this specific sequence to ensure the driver installs correctly without hardware conflicts:

Disconnect the Device: Do NOT have the Edgeport plugged into your computer when you start the installation.

Download Driver: Obtain the official Digi Edgeport driver v6.05 (often listed as file 40002537_6.05_N.exe).

Run as Administrator: Right-click the downloaded .exe file and select Run as Administrator.

Complete the Setup: Click the Setup button. A black command window will appear during the process; wait for it to disappear completely. Although the Edgeport 1 is a legacy device,

Connect Hardware: Plug the Edgeport/1 into a USB port. Windows should now automatically detect the hardware and finish the final installation steps. Verification and Configuration

To confirm your device is working properly, use the built-in utility included with the driver:

Locate Utility: Go to Start > All Apps > Digi USB > Edgeport Configuration Utility.

Check Status: Your Edgeport/1 should appear under the General tab. Expanding the entry will show the assigned COM port.

Firmware: Connecting the device to a computer with this driver installed will automatically update its firmware if needed. Troubleshooting Tips

Driver Signing: If the installation fails due to security restrictions, you may need to temporarily disable driver signature enforcement in Windows settings.

COM Port Changes: Use the Edgeport Configuration Utility to manually reassign COM port numbers if they conflict with other hardware.

Do you need help reassigning specific COM port numbers for your serial application? Download the driver intended for Windows 10

How to install the Edgeport driver in Windows - Digi International

The official driver for the Digi Edgeport 1 on Windows 10 (64-bit) is the v6.05 Edgeport Driver Digi International 🛠️ Quick Installation Guide To ensure a clean setup, follow this specific sequence: Unplug the Device : Do not plug the Edgeport into your USB port yet. Download & Run latest v6.05 driver from the official Digi Support site Admin Rights : Right-click the file and select Run as Administrator Wait for Finish

: A black command window will appear; wait for it to close on its own. Connect Hardware

: Once the installer finishes, plug the Edgeport into your computer's USB port. Digi International 🔍 How to Verify and Manage

After installation, you can confirm the device is working using the Edgeport Configuration Utility Start Menu Launch the Edgeport Configuration Utility

tab; your device should be listed with its assigned COM port. Digi International 💡 Troubleshooting Tips Legacy Hardware

: If you have an older "Legacy" Edgeport, you may need version , which is also compatible with Windows 10. Direct Connection

: For best results, plug the device directly into a PC port rather than a USB hub. LED Indicators : A slow-blinking means the device is installed and ready for use. Digi International If you run into issues, let me know: Does your device have a specific part number (e.g., 301-1001-11)? Industrial (MEI) model or the standard commercial version? Are you seeing a specific error code in Device Manager?

How to install the Edgeport driver in Windows - Digi International