Acer G41m07 Motherboard Manual May 2026

The G41M07 typically features four SATA II (3Gb/s) ports. These are usually colored blue or black. If you are adding a modern SSD, note that while SATA III drives will work, they will be limited to SATA II speeds (approx. 280MB/s max transfer), which is still faster than an old mechanical HDD.

[2x5 pins, pins 1-9 odd, 2-10 even]
Pin 1: HDD LED (+)    Pin 2: Power LED (+)
Pin 3: HDD LED (-)    Pin 4: Power LED (-)
Pin 5: Ground         Pin 6: Power Button (+)
Pin 7: Reset Switch   Pin 8: Power Button (-)
Pin 9: NC/Key (missing pin)
Pin 10: No pin

The BIOS setup section explains how to configure the motherboard's BIOS settings, including: acer g41m07 motherboard manual

If your system won’t boot due to incorrect BIOS settings, locate the jumper near the CR2032 battery and the SATA ports.

This board usually has two DDR3 DIMM slots.

While Acer never printed a standalone Acer G41M07 Motherboard Manual, the information above covers 99% of what a repair technician or retro PC enthusiast needs. This board is a humble workhorse of the Core 2 Duo era—reliable but full of OEM quirks. The G41M07 typically features four SATA II (3Gb/s) ports

If you are troubleshooting, remember: Check the CMOS battery first, do not expect AHCI support, and treat the VRM kindly with a low-wattage CPU.

Have a specific question about a jumper or error beep code on your G41M07? Treat this article as your manual—check the specifications table first, then verify your RAM density.

Acer G41M07 is a micro-ATX motherboard commonly found in the Acer Veriton M275 The BIOS setup section explains how to configure

desktop. It utilizes the Intel G41 Express chipset (Northbridge) and Intel ICH7 (Southbridge) to support legacy Intel processors and early DDR3 memory. The Retro Web Technical Specifications CPU Socket : LGA 775. Supported Processors

: Intel Core 2 Quad, Core 2 Duo, Pentium Dual-Core, and Celeron (including 45nm Wolfdale and Yorkfield cores). : 2 x DDR3 DIMM slots. Supports up to of Dual Channel DDR3 1066/1333 MHz Expansion Slots 1 x PCI Express x16. 1 x PCI Express x1. 2 x 32-bit PCI slots. : 4 x SATA ports (typically 1.5 GB/s or 3.0 GB/s). Integrated Graphics

: Intel Graphics Media Accelerator X4500 (DirectX 10 support). Acer Community Front Panel Header Pinout For users moving this board to a new case, the front panel header (F_PANEL) typically follows this configuration: Acer Community : Pins 2 (+) and 4 (-). Power Switch : Pins 6 and 8. Reset Switch : Pins 5 and 7. : Pins 1 (+) and 3 (-). : Pins 12 and 14. Super User Rear I/O Ports : 1 x Mouse, 1 x Keyboard. : 1 x VGA (D-Sub). : 4 x USB 2.0 ports. : 1 x RJ-45 Ethernet port (Realtek 10/100). : 3 x Jacks (Line-in, Line-out/Speaker, Mic-in). The Retro Web Installation & Maintenance Clear CMOS

: Use the onboard 3-pin jumper to reset BIOS settings if the system fails to post after hardware changes. Power Supply

: Requires a standard 24-pin ATX power connector and a 4-pin 12V CPU power connector. : For legacy support, refer to the Acer Support Site or archived service guides for the Veriton M275 files or a schematic diagram for component-level repair? Acer G41M07 - The Retro Web